Bearing shell Grimeca front | Pony GTX Beta 521 (P8925)

Wheel bearing shell Ø 32 mm bright steel

Material: Steel · Ø outside: 32 mm · Ø inside: 14 mm · Ø Bundle: 37 mm · Height: 14.25 mm

swiing® revival 1/4" balls Ø 6.35 mm (22 pcs.)

Manufacturer: swiing® revival parts · Material: Steel · Surface: hardened & ground · Number of components: 22 pcs · Ø ball [inch] / [mm]: 1/4" (6.35 mm) · Area of application: Standard

Motorex Lithium Grease 190 EP 400 g

Manufacturer: Motorex · Area of application: Chemistry · Area of application: Fat · Contents [g]: 400 g · Temperature resistance (min.): -30 - 120 °C

Motorex High Pressure Grease 3000 850 g

Manufacturer: Motorex · Area of application: Chemistry · Area of application: Fat · Contents [g]: 850 g · Hazard warning: Causes serious eye irritation · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Temperature resistance (min.): -30 - 150 °C

Bearing cone M11x1 mm

Material: Steel · Surface: gas nitrided · Color: graphite colors · Ø outside: 19 mm · Thread type: MF11x1 (fine pitch thread) · Height: 12 mm · Width across flats SW: 15 mm · Ø ball [inch] / [mm]: 1/4" (6.35 mm) · Ø ball [inch] / [mm]: 3/16" (4.78 mm) · Ø ball [inch] / [mm]: 7/32" (5.56 mm)

Motorex Bike Grease 100 g

Temperature resistance (min.): -30 - 120 °C · Manufacturer: Motorex · Area of application: Chemistry · Area of application: Fat · Contents [g]: 100 g

swiing® revival front wheel axle set | Pony GTX 521

Manufacturer: swiing® revival parts · Material: Chrome steel (known as Nirosta®) · Material: Steel · Surface: galvanized (blue) · Thread type: MF11x1 (fine pitch thread) · Ø shaft: 10.25 mm · Total length: 150 mm · Thread length: 55 mm · Thread length: 65 mm · Shank length: 25 mm · Ball bearing closed: No · Ø ball [inch] / [mm]: 1/4" (6.35 mm)

NTN wheel bearing 12/28/8 rear cast hub Leleu | Puch Maxi

Bearing type: Deep groove ball bearing · Stock number: 6001 · Ø inside: 12 mm · Ø outside: 28 mm · Width: 8 mm · Inner ring width: 12 mm · Manufacturer: NTN · Ball bearing closed: Yes · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CM (special/noise-reduced) · Bearing cage: "-" Sheet steel cage ball-guided · Groove ring: No · Material: Plastic · Material: Steel · Surface: blank · Area of application: Standard

swiing® revival 3/16" balls Ø 4.78 mm (26 pcs.)

Ø ball [inch] / [mm]: 3/16" (4.78 mm) · Number of components: 26 pcs · Manufacturer: swiing® revival parts · Material: Steel · Surface: hardened & ground · Area of application: Standard

swiing® revival 7/32" balls Ø 5.56 mm (22 pcs.)

Manufacturer: swiing® revival parts · Material: Steel · Surface: hardened & ground · Number of components: 22 pcs · Ø ball [inch] / [mm]: 7/32" (5.56 mm) · Area of application: Standard

Eurol ball bearing grease 110 g

Manufacturer: Eurol · Contents [g]: 110 g · Temperature resistance (min.): -30 - 120 °C · Area of application: Chemistry · Area of application: Fat

Wheel bearing shell Ø 30 mm

Material: Steel · Surface: galvanized (blue) · Ø inside: 25.9 mm · Ø outside: 30 mm · Height: 13 mm · Ø Bundle: 33 mm · Ø bore: 15 mm

swiing® revival 1/4" balls Ø 6.35 mm (22 pcs.)

Manufacturer: swiing® revival parts · Material: Steel · Surface: hardened & ground · Number of components: 22 pcs · Ø ball [inch] / [mm]: 1/4" (6.35 mm) · Area of application: Standard

ESJOT sprocket 40 teeth (4/5/6 hole) Ø 98 mm cranked black

Chain pitch: 1/2" x 3/16" · Chain type: 415H · Manufacturer: ESJOT · Material: Steel · Surface: powder-coated · Ø inside: 98 mm · Number of teeth: 40 pcs · Ø bolt circle: 115 mm · Thickness: 4.5 mm · Color: black · Number of fixing points: 4 pcs · Ø mounting hole: 7 mm · Cranking (offset): 12 mm

swiing® revival bearing cone M11x1

Manufacturer: swiing® revival parts · Surface: gas nitrided · Color: black · Ø outside: 17.95 mm · Ø ball [inch] / [mm]: 7/32" (5.56 mm) · Thread type: MF11x1 (fine pitch thread) · Height: 14.15 mm · Width across flats SW: 15 mm

Bearing cone M11x1 mm

Material: Steel · Surface: gas nitrided · Color: graphite colors · Ø outside: 19 mm · Thread type: MF11x1 (fine pitch thread) · Height: 12 mm · Width across flats SW: 15 mm · Ø ball [inch] / [mm]: 1/4" (6.35 mm) · Ø ball [inch] / [mm]: 3/16" (4.78 mm) · Ø ball [inch] / [mm]: 7/32" (5.56 mm)

swiing® revival wheel axle M11x1 x 180

Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Total length: 180 mm · Thread type: MF11x1 (fine pitch thread) · Ø shaft: 10.95 mm · Thread length: 75 mm · Shank length: 30 mm