- 10 %
Not so nice 
Pinasco «Slave» engine case with crankshaft (43 mm stroke / 12 mm KoBo) and double intake suitable for your Piaggio Ciao, Si, Bravo, Boxer, Grillo moped / moped.
The Pinasco «Power Casing» engine case is supplied with a specially developed crankshaft, which has a wider cheek for controlling the intake at the rear intake.
On this case, a standard 13 mm Dellorto SHA carburettor can be installed at the rear on the one hand, and any side carburettor with a 24 mm connection on the reed system on the other. The frame may have to be adapted in this case.
With this dual carburetor system, you can tease the last bit of horsepower out of your motorcycle.
The following parts are included in the scope of delivery:
- Rear intake flange (connection 16 mm, &slash; inside 13 mm)
- Side membrane system incl. sealing plug for the 13 mm flange if this is not used
- Mounting material for diaphragm flange (connection 24 mm, Ø inside 20 mm)
- Cylinder stud bolt
- Engine housing (Ø for cylinder neck up to 46 mm outer diameter)
- Engine housing screws
- Crankshaft Pinasco Competition with 43 mm stroke and 12 mm piston pin (axe 12)
- Installation instructions in English & Italian
No housing seal is supplied. Sealing compound is used for sealing.
We recommend using the 42 mm Pinasco cylinder kit for this racing gear. In addition, only electronic ignitions can be fitted to this housing.
If the engine is installed in a Piaggio Ciao frame, some material must be removed from the right-hand side of the housing and cylinder; this is described in the installation instructions.
Corresponding add-on parts such as sealant, racing kit, racing ignition etc. can be found in the accessories section.
Mäsig-läsig! – We strive to offer you the widest range of moped spare parts. However, this product is of rather poor quality and is not recommended by us. Should you nevertheless choose this item, we understand, but cannot offer you any guarantee or exchange.
Quality product from the Italian manufacturer Pinasco.
| Manufacturer | Pinasco |
| Material | Aluminum |
| Crankshaft stroke | 43 mm |
| Ignition type | Electronic |
| Piaggio | Ciao - P , SC , PX , C24 Si Bravo / Super Bravo Boxer Grillo |
Accessories & related products
Dell'Orto 19 mm PHBG CS carburetor hand choke
Nominal diameter: 19 mm · Manufacturer: Dell'Orto · Area of application: Racing · Area of application: Tuning · Component group Carburetor: Carburetor complete · Material: Aluminum · Color: black · Carburetor type: PHBG CS · Width: 70 mm · Ø without reducing sleeve: 26 mm · Height: 124 mm · Ø Inside entrance: 19 mm · Ø Internal connection: 24 mm · Ø Output inside: 19 mm · Mounting type: Plug connection clamped · Ø Air filter connection: 32 mm · Ø Air filter connection: 60 mm · Air filter connection thread: MF32x1.25 (fine pitch thread) · Ø fuel hose connection: 5.4 mm · Ø fuel hose connection: 6 mm · Total length: 82 mm · Mixed oil connection: Yes · Vacuum connection: Yes · Choke control: Hand choke · Choke nozzle size: 60 · Nozzle thread: M5x0.8 (standard thread) · Camouflaged: No · Nozzle size: 75 · Size of secondary nozzle: 45
EUR 142.30
Malossi racing ignition 12V | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Malossi · Area of application: High End · Area of application: Performance · Area of application: Racing · Area of application: Tuning · Material: Steel · Ø Internal flywheel: 80.5 mm · Light coil voltage: 12 V · Performance: 90 W · Direction of rotation: right · Ø Flywheel outside: 105 mm · Ø Flywheel outside: 139.5 mm · Ø cable: 7 mm · Mounting type: Screws · Number of fixing points: 2 pcs · Weight: 804 g · Weight: 890 g
EUR 474.50
SKF 6202 C3 ball bearing 15/35/11
Bearing type: Deep groove ball bearing · Bearing cage: Sheet steel cage ball-guided · Stock number: 6202 · Inner ring width: 11 mm · Manufacturer: SKF · Bearing clearance: C3 · Width: 11 mm · Ø inside: 15 mm · Ø outside: 35 mm · Puch OEM number: 900.4.6202
EUR 11.80
Elring Dirko HT sealing compound gray (silicone) 70 ml permanently elastic up to 315°C
Manufacturer: Elring · Area of application: Chemistry · Material: Silicone · Contents: 70 ml · Color: gray · Hazard warning: Causes damage to organs through prolonged or repeated exposure · Temperature resistance (min.): -60 - 315 °C · Gap dimension (max.): 2 mm
EUR 23.60
EUR 337.14/l
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Pinasco · Material: Aluminum · Material: Carbon · Ø Internal flywheel: 106 mm · Surface: varnished · Direction of rotation: right · Ø cone small inside: 12.4 mm · Ø cone large inside: 14.5 mm · Height: 38.7 mm · Ø Flywheel outside: 135 mm · Cone length: 12.5 mm · Cone ratio: 1:5 · Thread type: MF16x1 (fine pitch thread) · Thread length: 7.5 mm · Weight: 650 g
EUR 249.00
Dell'Orto 13/13 SHA carburetor hand choke | Piaggio Ciao P, SC
Nominal diameter: 13 mm · Manufacturer: Dell'Orto · Area of application: Tuning · Component group Carburetor: Carburetor complete · Material: Aluminum · Color: black · Carburetor type: SHA (Piaggio) · Width: 60 mm · Ø without reducing sleeve: 18 mm · Height: 110 mm · Ø Inside entrance: 13 mm · Ø Internal connection: 16 mm · Ø Output inside: 13 mm · Mounting type: Plug connection clamped · Ø Air filter connection: 50.9 mm · Ø fuel hose connection: 5.2 mm · Ø fuel hose connection: 6 mm · Total length: 55 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Camouflaged: No · Nozzle size: 66
EUR 82.90
Not in stock
Malossi oil seal FPM 15/24/5 A crankshaft | Piaggio Ciao, SI, Bravo, Boxer
Shaft seal type: A - With rubberized outer part / one sealing lip. · Manufacturer: Malossi · Place of use: Crankshaft · Material: FPM / FKM (colloquially known as Viton) · Width: 5 mm · Ø inside: 15 mm · Temperature resistance (min.): -30 - 200 °C · Ø outside: 24 mm
EUR 17.00
Pinasco 42 mm cylinder kit EVOTEN 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Nominal diameter: 42 mm · Manufacturer: Pinasco · Area of application: Tuning · Material: Aluminum · Surface: varnished · Displacement: 60 ccm · Crankshaft stroke: 43 mm · Ø Outlet outside: 22.5 mm · Ø piston pin (B): 12 mm · Outlet type: clamped · Number of fixing points: 3 pcs · Decompressor: Yes · Camouflaged: No
EUR 438.90
Explore categories from Gearbox & housing (motor)
Working late? Evening hours on Thursday until 20:00
